papaedmund

Hi, Material for feature wall: 1.Normal MDF board or plywood and paint it over 2.Normal plywood and laminate it with strips design 3.Normal playwood and wallpaper it All these need some carpentry skill to mount it to wall. Cheers!

Hi, Go find those industrial factories and look for people that do carpentry work and ask them to cut for you the sizes you want for the shelves. Good Luck

Hi, You can ask carpenter to make 2 plywoods to the size you want, and just glue and clamp it to the glass.

Hi, I say reasonable. 1.$180-$220 normal swing doors in laminate 2.$220-$250 wooden sliding doors with simple design 3.$250-$300 alluminium frame sliding doors with simple design(glass and laminate) 4.$300 above alluminium frame sliding doors with complicated design Afterall is only a guideline.It depend on: 1.material used for internal of wardrobe 2.internal layout (more drawers or shelves) 3.complicated design? Hope this help.

Hi, Yes.... mostly is is 86cm.Since its custom made,you can do what ever height to suit you. Usually for sink area people will request to do a bit higher if he/she is tall.(depend how deep sink is) The Hob area can be slightly lower if you are short person.But all this must be accepted by you because it will have (up and down) look for the surface top. Afterall, its just depend on the person's height.He/She should know. Hope my explain helps

Hi, You may try here: Mactech Industrial Building Preference Manufacturing Pte Ltd No2.Kallang Pudding road #01-02/06/07 Tel:67465185

Hi, Actually not advisable to use paint over laminate surface because it will come off easily if accidentally knock onto it or scratch. May i know why you want to paint over the laminate?

Yes, im a carpenter for many years.

Hi, Laminate usually comes in 4 x 8 ft or even bigger.You did not mention how big the laminate you intend to cut. If you intend to DIY at home ,best is to ask a factory that uses a saw machine to cut out for you the sizes you need and then bring it home. Anyway: 1.Place laminate in FLAT area,do your marking,use a ruler or straight wood(if you have),press and hold,cut with a stronger and harder blade pen knife. Need to cut a few times down until laminate is about to break or you may just cut through if the laminate is those thin ones. IMPORTANT:Be very very careful when doing this when cutting.Like you said,you need to get a first cut score line and softly and slowly the second cut and so on.You may get deep cut if you did not do it properly.I have seen people got 10 needle stiches from doctor when they cut themselves 2.Laminate bigger by about 10-15mm.Use a file and wood plane to have a good finish.(need skill) 3.Router is the best if you have one and know how to use it. Hope you understand my words and of help. Good Luck

If only compare these 2 brands,Jenning is better. Other good brands are: LamChuan..EDL...TAK...SengLee...Formica

Hi, Are you looking for this? Lea Huat Hardware Industries Blk 3018 Bedok North st 5 (EastLink) #01-01 S486132 Tel: 64488956

Hi, Little Too expensive for me Afterall it depend what kind of material is used. But if you have seen a finished project done by them before and you are satisfied with the workmanship,then go ahead.

Hi, I think you are looking for this Lee Huat Hardware Industries Blk 3018 Bedok North St 5(East Link) #01-01 S'pore 486132 Tel:64488956

Hi, Would like to share with you guys my DIY TV feature wall and console. This is done around 1 week before chinese new year. some pictures: My link

Try Thye Seng Hardware Enterprise Pte Ltd 1.No 122 Sims Avenue , Gelyang, Singapore 387445 Tel : 6747 7415 , 6747 4571 2.No. 362 Changi Road, 8.9 km, Singapore 419823 Tel: 6440 6206 , 6440 8614

Hi, Have you try this?

Hi, For DIY shelves or doors usually plywood will do.Kapor or chengai wood are mainly for outdoors use and need to varnish or paint. Depending on the size for the shelves or doors you intend to DIY,plywood comes in 4ft x 8ft and you just need to cut to size. For DIY door you need: 1.20mm thick plywood(三合板) with both side paste with nice coloured pvc or one side only with the other paste with laminate yourself. 2.need to drill some holes for the hinges area(shorter door 2 holes longer doors 3 holes) 3.need to wrap up four sides of the door using either ABS trimming,laminate or pvc. Note:above door is for concealed hinge. Hope i have a little help to my 1st question

Hi, First time at RenoTalk here. I myself has been a carpenter for many years and would like to share my experience in carpentry works with everyone. People who have any question at DIY on carpentry works may post here to share with everyone or may PM me.(post with pictures will be good) Thanks and sorry for the bad english.